.
EditStep 1 — 555 Timer Blinky
Check the kit to make sure you have two LEDs, the 555 timer, a capacitor, the four resistors shown, and a battery box. You'll need to supply a small amount of hookup wire.
Place the protoboard in the helping hands in the orientation shown here.
To solder each component, you'll keep the board in the helping hands and roll it over, away from you so that it's reversed and upside down.
Place the 555 timer into the protoboard as shown, paying attention to the notch in the 555 timer (it should be pointing up).
Flip the board over and solder the pads shown on the right-hand side of the image.
Place the 1 megohm resistor (Brown, Black, Green) into the board as shown.
Flip the board over and solder the resistor into place. Trim the leads when you're done.
Place the second 1 megohm resistor into the board.
Flip the board over, solder the resistor in place, and trim the leads.
Prepare a short length of red hookup wire. This wire will be hooked up to the positive side of the battery and provide power to the chip.
Cut it so it's a little longer than the length shown.
Strip the ends to about 1/2 an inch.
Tin the ends of the wire.
Insert the wire into the board as shown, flip it over, and solder it into place. If you have any excess, trim it.
Prepare a length of green wire (or blue or yellow) as shown.
Insert it into the board as shown.
Solder it into place and trim any excess.
Prepare another length of red jumper wire.
Place it in the PCB as shown.
Solder it into place and trim any excess.
Connect the battery and watch it blink!
The LEDs blink in an alternating fashion because one is connected "backwards". When the 555 timer's output pin goes "low", electricity flows through that LED. The other LED is connected normally.
Category
555,
555 blinker,
555 timer,
555 timer Blinky,
timer
.
EditStep 1 — 555 Timer Blinky
Check the kit to make sure you have two LEDs, the 555 timer, a capacitor, the four resistors shown, and a battery box. You'll need to supply a small amount of hookup wire.
Place the protoboard in the helping hands in the orientation shown here.
To solder each component, you'll keep the board in the helping hands and roll it over, away from you so that it's reversed and upside down.
Place the 555 timer into the protoboard as shown, paying attention to the notch in the 555 timer (it should be pointing up).
Flip the board over and solder the pads shown on the right-hand side of the image.
Place the 1 megohm resistor (Brown, Black, Green) into the board as shown.
Flip the board over and solder the resistor into place. Trim the leads when you're done.
Place the second 1 megohm resistor into the board.
Flip the board over, solder the resistor in place, and trim the leads.
Prepare a short length of red hookup wire. This wire will be hooked up to the positive side of the battery and provide power to the chip.
Cut it so it's a little longer than the length shown.
Strip the ends to about 1/2 an inch.
Tin the ends of the wire.
Insert the wire into the board as shown, flip it over, and solder it into place. If you have any excess, trim it.
Prepare a length of green wire (or blue or yellow) as shown.
Insert it into the board as shown.
Solder it into place and trim any excess.
Prepare another length of red jumper wire.
Place it in the PCB as shown.
Solder it into place and trim any excess.
Connect the battery and watch it blink!
The LEDs blink in an alternating fashion because one is connected "backwards". When the 555 timer's output pin goes "low", electricity flows through that LED. The other LED is connected normally.
Category
555,
555 blinker,
555 timer,
555 timer Blinky,
timer
